Up next New Truck News | Electric Hummer serving the Armed Forces?? Published on July 31, 2020 Author SOLOMON LUNGER Tags ’65-’72, F-100 Builder’s Guide, f100, QA1, Share article Facebook 0 Twitter 0 Mail 0 QA1 Suspension ’65-’72 F100 Rear Install In the last issue of F-100 Builder’s Guide you saw Joey and the team at Evolutionary Rides take our ’72 F-100 Oscar The Bump off the frame, strip the frame down to the rails and install the QA1 front suspension. Because we’re emphasizing performance in this issue, we’re going to show you how the QA1 rear suspension setup goes together in a ’65-’72 truck. We were very happy to be ditching the factory leaves and installing a torque-arm style rear setup. Why? For one, it maximizes performance while minimizing suspension bind. And two, from speaking with the knowledgeable techs at QA1, we are definitely excited to take this onto a track and around some corners.Subscribe to our weekly newsletter This complete bolt-in system adds unprecedented adjustability to your truck without any welding. It can be installed in any home garage and can even be done with the bed still on (if you’re not in the middle of a restoration project like we are). You can get a 4- to 7-inch drop out of this system, it is about 100 pounds lighter than the stock suspension, and it looks just as good as it performs. Here’s an overall look at the full QA1 rear system. Tools needed include a floor jack, jack stands, drill with ¼-inch and 7/16-inch drill bits, wrenches, ratchets and socket sets, a torque wrench, grinder or air chisel, some anti-seize and, most importantly, some cool refreshments if this happens to be a “stay at home” project. This is by no means is meant to be a step-by-step instruction set; for that you can go to www.QA1.net/F100. What this is meant to be is a guide to show you what all this system entails and why we chose to go with this setup for our project. The guys at Evolutionary Rides said that this is an easy, very straightforward install. What we have done here might not be exactly how you’ll do it at home since we had the truck taken off the frame for our restoration. Joey and his team have installed a few of these QA1 kits already, so they certainly know some of the tricks to getting it done quickly and safely. They removed some of the crossmembers that you do not need to remove, but we are going to be adding some custom ones back in later. We didn’t get to it yet (we will be setting ride height, and final wheel/tire choices down the road), but there will be final adjustments once we put the chassis back together after powdercoating. Last but no least, make sure that you enjoy your classic trucks and get out there and drive them! [divider]SOURCES[/divider] QA1 Motorsports 800-721-7761, orders 952-985-5675, tech support www.QA1.net Evolutionary Rides 352-835-1355 evorides@yahoo.com www.facebook.com/evolutionaryrides Like we mentioned, our project is a long-term restoration, so we pulled the frame completely out from under the truck. Evolutionary Rides made quick work of cutting and removing the rivets and striping our chassis to bare bones. A clean slate; our factory chassis will be getting some major love. Next, a template was used to mark for the notch, and it was cut out. The frame plates were marked, holes drilled and installed. Next up, we installed the QA1 brackets and mounting components on the rear axle. Here’s a look at the rear axle with bracketry installed (keep in mind we’re currently just mocking up as we will be powdercoating and reassembling our frame/suspension later). Evolutionary Rides bolted up the trailing arm links. Next, our favorite part: bolting in the gorgeous QA1 coilovers that will be the heart and soul of this new performance-minded suspension setup. We installed the brackets and rear sway bar. Next up, we installed the torque arm to the rear axle. We installed the torque-arm crossmember. Then we bolted the torque arm to the front crossmember. We didn’t fully tighten or adjust everything just yet, as we still have to dial in our stance and wheel tire setup that will be done after the frame comes back from powder. The Panhard bar and brace bar were also mocked up and fully cycled And here she is. We can’t wait to get our frame back from powdercoat and fully assemble the system to put all of it to the test at our local track. Stay tuned!
QA1’s 1969 Dodge D-100 For decades, the Dodge Sweptline trucks have been a hard pill to swallow. Even with their capable powerplants and unique, beautiful styling, they never quite […] streettrucks January 03, 2023 Department Editor Features HEADLINE Latest Profiles Reader Rides Uncategorized
READER RIDES | HOMETOWN HEROES A Clean C-20 Bruce Hauser’s ’67 Chevrolet C-20 has been with him since high school. Considering Bruce is 68 years young, the dedication he’s had […] STREET TRUCKS STAFF May 31, 2019 Department Latest Profiles
Making Steady Progress on Our ’67 C10 Project last chance Part 2 We have been hard at work on Project Last Chance and have made a lot of progress since the last […] JOSH MCPHERSON December 06, 2022 Blood Sweat and Gears c10 C10 Builders Guide Department HEADLINE Latest Profiles Reader Rides Tech
Photographer Spotlight | Phil Gordon The month of May’s Photographer spotlight is on Phil Gordon. I Hate Phil. If you don’t hate Phil now, you will by the end of […] Adam Johnson May 04, 2022 Department Industry News Latest Press Release Product Reviews Profiles